ssh_config(5)
NAME
ssh_config - OpenSSH SSH client configuration files
SYNOPSIS
~/.ssh/config
/etc/ssh/ssh_config
DESCRIPTION
ssh(1) obtains configuration data from the following sources in the
following order:
1. command-line options
2. user's configuration file (~/.ssh/config)
3. system-wide configuration file (/etc/ssh/ssh_config)
For each parameter, the first obtained value will be used. The
configuration files contain sections separated by ``Host'' spec-
ifications, and that section is only applied for hosts that
match one of the patterns given in the specification. The
matched host name is usually the one given on the command line
(see the CanonicalizeHostname option for exceptions.)
Since the first obtained value for each parameter is used, more
host-specific declarations should be given near the beginning of
the file, and general defaults at the end.
The configuration file has the following format:
Empty lines and lines starting with `#' are comments. Otherwise
a line is of the format ``keyword arguments''. Configuration
options may be separated by whitespace or optional whitespace
and exactly one `=' ; the latter format is useful to avoid the
need to quote whitespace when specifying configuration options
using the ssh, scp, and sftp -o option. Arguments may option-
ally be enclosed in double quotes (") in order to represent
arguments containing spaces.
The possible keywords and their meanings are as follows (note
that keywords are case-insensitive and arguments are case-sensi-
tive):
Host Restricts the following declarations (up to the next Host or
Match keyword) to be only for those hosts that match one of the
patterns given after the keyword. If more than one pattern is
provided, they should be separated by whitespace. A single `*'
as a pattern can be used to provide global defaults for all
hosts. The host is usually the hostname argument given on the
command line (see the CanonicalizeHostname option for excep-
tions.)
A pattern entry may be negated by prefixing it with an exclama-
tion mark (`!'.) If a negated entry is matched, then the Host
entry is ignored, regardless of whether any other patterns on
the line match. Negated matches are therefore useful to provide
exceptions for wildcard matches.
See PATTERNS for more information on patterns.
Match Restricts the following declarations (up to the next Host or
Match keyword) to be used only when the conditions following the
Match keyword are satisfied. Match conditions are specified
using one or more criteria or the single token all which always
matches. The available criteria keywords are: canonical, exec,
host, originalhost, user, and localuser. The all criteria must
appear alone or immediately after canonical. Other criteria may
be combined arbitrarily. All criteria but all and canonical
require an argument. Criteria may be negated by prepending an
exclamation mark (`!'.)
The canonical keyword matches only when the configuration file
is being re-parsed after hostname canonicalization (see the
CanonicalizeHostname option.) This may be useful to specify
conditions that work with canonical host names only. The exec
keyword executes the specified command under the user's shell.
If the command returns a zero exit status then the condition is
considered true. Commands containing whitespace characters must
be quoted. The following character sequences in the command
will be expanded prior to execution: `%L' will be substituted by
the first component of the local host name, `%l' will be substi-
tuted by the local host name (including any domain name), `%h'
will be substituted by the target host name, `%n' will be sub-
stituted by the original target host name specified on the com-
mand-line, `%p' the destination port, `%r' by the remote login
username, and `%u' by the username of the user running ssh(1).
The other keywords' criteria must be single entries or comma-
separated lists and may use the wildcard and negation operators
described in the PATTERNS section. The criteria for the host
keyword are matched against the target hostname, after any sub-
stitution by the Hostname or CanonicalizeHostname options. The
originalhost keyword matches against the hostname as it was
specified on the command-line. The user keyword matches against
the target username on the remote host. The localuser keyword
matches against the name of the local user running ssh(1) (this
keyword may be useful in system-wide ssh_config files).
AddKeysToAgent
Specifies whether keys should be automatically added to a run-
ning ssh-agent(1). If this option is set to ``yes'' and a key
is loaded from a file, the key and its passphrase are added to
the agent with the default lifetime, as if by ssh-add(1). If
this option is set to ``ask'', ssh will require confirmation
using the SSH_ASKPASS program before adding a key (see ssh-
add(1) for details). If this option is set to ``confirm'', each
use of the key must be confirmed, as if the -c option was speci-
fied to ssh-add(1). If this option is set to ``no'', no keys
are added to the agent. The argument must be ``yes'', ``con-
firm'', ``ask'', or ``no''. The default is ``no''.
AddressFamily
Specifies which address family to use when connecting. Valid
arguments are ``any'', ``inet'' (use IPv4 only), or ``inet6''
(use IPv6 only). The default is ``any''.
BatchMode
If set to ``yes'', passphrase/password querying will be dis-
abled. This option is useful in scripts and other batch jobs
where no user is present to supply the password. The argument
must be ``yes'' or ``no''. The default is ``no''.
BindAddress
Use the specified address on the local machine as the source
address of the connection. Only useful on systems with more
than one address. Note that this option does not work if
UsePrivilegedPort is set to ``yes''.
CanonicalDomains
When CanonicalizeHostname is enabled, this option specifies the
list of domain suffixes in which to search for the specified
destination host.
CanonicalizeFallbackLocal
Specifies whether to fail with an error when hostname canonical-
ization fails. The default, ``yes'', will attempt to look up
the unqualified hostname using the system resolver's search
rules. A value of ``no'' will cause ssh(1) to fail instantly if
CanonicalizeHostname is enabled and the target hostname cannot
be found in any of the domains specified by CanonicalDomains.
CanonicalizeHostname
Controls whether explicit hostname canonicalization is per-
formed. The default, ``no'', is not to perform any name rewrit-
ing and let the system resolver handle all hostname lookups. If
set to ``yes'' then, for connections that do not use a Proxy-
Command, ssh(1) will attempt to canonicalize the hostname speci-
fied on the command line using the CanonicalDomains suffixes and
CanonicalizePermittedCNAMEs rules. If CanonicalizeHostname is
set to ``always'', then canonicalization is applied to proxied
connections too.
If this option is enabled, then the configuration files are pro-
cessed again using the new target name to pick up any new con-
figuration in matching Host and Match stanzas.
CanonicalizeMaxDots
Specifies the maximum number of dot characters in a hostname
before canonicalization is disabled. The default, ``1'', allows
a single dot (i.e. hostname.subdomain).
CanonicalizePermittedCNAMEs
Specifies rules to determine whether CNAMEs should be followed
when canonicalizing hostnames. The rules consist of one or more
arguments of source_domain_list :target_domain_list, where
source_domain_list is a pattern-list of domains that may follow
CNAMEs in canonicalization, and target_domain_list is a pattern-
list of domains that they may resolve to.
For example, ``*.a.example.com:*.b.example.com,*.c.example.com''
will allow hostnames matching ``*.a.example.com'' to be canoni-
calized to names in the ``*.b.example.com'' or ``*.c.exam-
ple.com'' domains.
CertificateFile
Specifies a file from which the user's certificate is read. A
corresponding private key must be provided separately in order
to use this certificate either from an IdentityFile directive or
-i flag to ssh(1), via ssh-agent(1), or via a PKCS11Provider.
The file name may use the tilde syntax to refer to a user's home
directory or one of the following escape characters: `%d' (local
user's home directory), `%u' (local user name), `%l' (local host
name), `%h' (remote host name) or `%r' (remote user name).
It is possible to have multiple certificate files specified in
configuration files; these certificates will be tried in
sequence. Multiple CertificateFile directives will add to the
list of certificates used for authentication.
ChallengeResponseAuthentication
Specifies whether to use challenge-response authentication. The
argument to this keyword must be ``yes'' or ``no''. The default
is ``yes''.
CheckHostIP
If this flag is set to ``yes'', ssh(1) will additionally check
the host IP address in the known_hosts file. This allows ssh to
detect if a host key changed due to DNS spoofing and will add
addresses of destination hosts to ~/.ssh/known_hosts in the
process, regardless of the setting of StrictHostKeyChecking. If
the option is set to ``no'', the check will not be executed.
The default is ``yes''.
Cipher Specifies the cipher to use for encrypting the session in proto-
col version 1. Currently, ``blowfish'', ``3des'', and ``des''
are supported. des is only supported in the ssh(1) client for
interoperability with legacy protocol 1 implementations that do
not support the 3des cipher. Its use is strongly discouraged
due to cryptographic weaknesses. The default is ``3des''.
Ciphers
Specifies the ciphers allowed for protocol version 2 in order of
preference. Multiple ciphers must be comma-separated. If the
specified value begins with a `+' character, then the specified
ciphers will be appended to the default set instead of replacing
them.
The supported ciphers are:
3des-cbc
aes128-cbc
aes192-cbc
aes256-cbc
aes128-ctr
aes192-ctr
aes256-ctr
aes128-gcm@openssh.com
aes256-gcm@openssh.com
arcfour
arcfour128
arcfour256
blowfish-cbc
cast128-cbc
chacha20-poly1305@openssh.com
The default is:
chacha20-poly1305@openssh.com,
aes128-ctr,aes192-ctr,aes256-ctr,
aes128-gcm@openssh.com,aes256-gcm@openssh.com,
aes128-cbc,aes192-cbc,aes256-cbc,3des-cbc
The list of available ciphers may also be obtained using the -Q
option of ssh(1) with an argument of ``cipher''.
ClearAllForwardings
Specifies that all local, remote, and dynamic port forwardings
specified in the configuration files or on the command line be
cleared. This option is primarily useful when used from the
ssh(1) command line to clear port forwardings set in configura-
tion files, and is automatically set by scp(1) and sftp(1). The
argument must be ``yes'' or ``no''. The default is ``no''.
Compression
Specifies whether to use compression. The argument must be
``yes'' or ``no''. The default is ``no''.
CompressionLevel
Specifies the compression level to use if compression is
enabled. The argument must be an integer from 1 (fast) to 9
(slow, best). The default level is 6, which is good for most
applications. The meaning of the values is the same as in
gzip(1). Note that this option applies to protocol version 1
only.
ConnectionAttempts
Specifies the number of tries (one per second) to make before
exiting. The argument must be an integer. This may be useful
in scripts if the connection sometimes fails. The default is 1.
ConnectTimeout
Specifies the timeout (in seconds) used when connecting to the
SSH server, instead of using the default system TCP timeout.
This value is used only when the target is down or really
unreachable, not when it refuses the connection.
ControlMaster
Enables the sharing of multiple sessions over a single network
connection. When set to ``yes'', ssh(1) will listen for connec-
tions on a control socket specified using the ControlPath argu-
ment. Additional sessions can connect to this socket using the
same ControlPath with ControlMaster set to ``no'' (the default).
These sessions will try to reuse the master instance's network
connection rather than initiating new ones, but will fall back
to connecting normally if the control socket does not exist, or
is not listening.
Setting this to ``ask'' will cause ssh to listen for control
connections, but require confirmation using ssh-askpass(1). If
the ControlPath cannot be opened, ssh will continue without con-
necting to a master instance.
X11 and ssh-agent(1) forwarding is supported over these multi-
plexed connections, however the display and agent forwarded will
be the one belonging to the master connection i.e. it is not
possible to forward multiple displays or agents.
Two additional options allow for opportunistic multiplexing: try
to use a master connection but fall back to creating a new one
if one does not already exist. These options are: ``auto'' and
``autoask''. The latter requires confirmation like the ``ask''
option.
ControlPath
Specify the path to the control socket used for connection shar-
ing as described in the ControlMaster section above or the
string ``none'' to disable connection sharing. In the path,
`%L' will be substituted by the first component of the local
host name, `%l' will be substituted by the local host name
(including any domain name), `%h' will be substituted by the
target host name, `%n' will be substituted by the original tar-
get host name specified on the command line, `%p' the destina-
tion port, `%r' by the remote login username, `%u' by the user-
name and `%i' by the numeric user ID (uid) of the user running
ssh(1), and `%C' by a hash of the concatenation: %l%h%p%r. It
is recommended that any ControlPath used for opportunistic con-
nection sharing include at least %h, %p, and %r (or alterna-
tively %C) and be placed in a directory that is not writable by
other users. This ensures that shared connections are uniquely
identified.
ControlPersist
When used in conjunction with ControlMaster, specifies that the
master connection should remain open in the background (waiting
for future client connections) after the initial client connec-
tion has been closed. If set to ``no'', then the master connec-
tion will not be placed into the background, and will close as
soon as the initial client connection is closed. If set to
``yes'' or ``0'', then the master connection will remain in the
background indefinitely (until killed or closed via a mechanism
such as the ssh(1) ``Fl O No exit'' option). If set to a time
in seconds, or a time in any of the formats documented in
sshd_config(5), then the backgrounded master connection will
automatically terminate after it has remained idle (with no
client connections) for the specified time.
DynamicForward
Specifies that a TCP port on the local machine be forwarded over
the secure channel, and the application protocol is then used to
determine where to connect to from the remote machine.
The argument must be [bind_address:]port. IPv6 addresses can be
specified by enclosing addresses in square brackets. By
default, the local port is bound in accordance with the Gateway-
Ports setting. However, an explicit bind_address may be used to
bind the connection to a specific address. The bind_address of
``localhost'' indicates that the listening port be bound for
local use only, while an empty address or `*' indicates that the
port should be available from all interfaces.
Currently the SOCKS4 and SOCKS5 protocols are supported, and
ssh(1) will act as a SOCKS server. Multiple forwardings may be
specified, and additional forwardings can be given on the com-
mand line. Only the superuser can forward privileged ports.
EnableSSHKeysign
Setting this option to ``yes'' in the global client configura-
tion file /etc/ssh/ssh_config enables the use of the helper pro-
gram ssh-keysign(8) during HostbasedAuthentication. The argu-
ment must be ``yes'' or ``no''. The default is ``no''. This
option should be placed in the non-hostspecific section. See
ssh-keysign(8) for more information.
EscapeChar
Sets the escape character (default: `~' ) . The escape charac-
ter can also be set on the command line. The argument should be
a single character, `^' followed by a letter, or ``none'' to
disable the escape character entirely (making the connection
transparent for binary data).
ExitOnForwardFailure
Specifies whether ssh(1) should terminate the connection if it
cannot set up all requested dynamic, tunnel, local, and remote
port forwardings, (e.g. if either end is unable to bind and lis-
ten on a specified port). Note that ExitOnForwardFailure does
not apply to connections made over port forwardings and will
not, for example, cause ssh(1) to exit if TCP connections to the
ultimate forwarding destination fail. The argument must be
``yes'' or ``no''. The default is ``no''.
FingerprintHash
Specifies the hash algorithm used when displaying key finger-
prints. Valid options are: ``md5'' and ``sha256''. The default
is ``md5''.
ForwardAgent
Specifies whether the connection to the authentication agent (if
any) will be forwarded to the remote machine. The argument must
be ``yes'' or ``no''. The default is ``no''.
Agent forwarding should be enabled with caution. Users with the
ability to bypass file permissions on the remote host (for the
agent's Unix-domain socket) can access the local agent through
the forwarded connection. An attacker cannot obtain key mate-
rial from the agent, however they can perform operations on the
keys that enable them to authenticate using the identities
loaded into the agent.
ForwardX11
Specifies whether X11 connections will be automatically redi-
rected over the secure channel and DISPLAY set. The argument
must be ``yes'' or ``no''. The default is ``no''.
X11 forwarding should be enabled with caution. Users with the
ability to bypass file permissions on the remote host (for the
user's X11 authorization database) can access the local X11 dis-
play through the forwarded connection. An attacker may then be
able to perform activities such as keystroke monitoring if the
ForwardX11Trusted option is also enabled.
ForwardX11Timeout
Specify a timeout for untrusted X11 forwarding using the format
described in the TIME FORMATS section of sshd_config(5). X11
connections received by ssh(1) after this time will be refused.
The default is to disable untrusted X11 forwarding after twenty
minutes has elapsed.
ForwardX11Trusted
If this option is set to ``yes'', remote X11 clients will have
full access to the original X11 display.
If this option is set to ``no'', remote X11 clients will be con-
sidered untrusted and prevented from stealing or tampering with
data belonging to trusted X11 clients. Furthermore, the
xauth(1) token used for the session will be set to expire after
20 minutes. Remote clients will be refused access after this
time.
The default is ``no''.
See the X11 SECURITY extension specification for full details on
the restrictions imposed on untrusted clients.
GatewayPorts
Specifies whether remote hosts are allowed to connect to local
forwarded ports. By default, ssh(1) binds local port forward-
ings to the loopback address. This prevents other remote hosts
from connecting to forwarded ports. GatewayPorts can be used to
specify that ssh should bind local port forwardings to the wild-
card address, thus allowing remote hosts to connect to forwarded
ports. The argument must be ``yes'' or ``no''. The default is
``no''.
GlobalKnownHostsFile
Specifies one or more files to use for the global host key data-
base, separated by whitespace. The default is
/etc/ssh/ssh_known_hosts, /etc/ssh/ssh_known_hosts2.
GSSAPIAuthentication
Specifies whether user authentication based on GSSAPI is
allowed. The default is ``no''.
GSSAPIDelegateCredentials
Forward (delegate) credentials to the server. The default is
``no''.
HashKnownHosts
Indicates that ssh(1) should hash host names and addresses when
they are added to ~/.ssh/known_hosts. These hashed names may be
used normally by ssh(1) and sshd(8), but they do not reveal
identifying information should the file's contents be disclosed.
The default is ``no''. Note that existing names and addresses
in known hosts files will not be converted automatically, but
may be manually hashed using ssh-keygen(1).
HostbasedAuthentication
Specifies whether to try rhosts based authentication with public
key authentication. The argument must be ``yes'' or ``no''.
The default is ``no''.
HostbasedKeyTypes
Specifies the key types that will be used for hostbased authen-
tication as a comma-separated pattern list. Alternately if the
specified value begins with a `+' character, then the specified
key types will be appended to the default set instead of replac-
ing them. The default for this option is:
ecdsa-sha2-nistp256-cert-v01@openssh.com,
ecdsa-sha2-nistp384-cert-v01@openssh.com,
ecdsa-sha2-nistp521-cert-v01@openssh.com,
ssh-ed25519-cert-v01@openssh.com,
ssh-rsa-cert-v01@openssh.com,
ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521,
ssh-ed25519,ssh-rsa
The -Q option of ssh(1) may be used to list supported key types.
HostKeyAlgorithms
Specifies the host key algorithms that the client wants to use
in order of preference. Alternately if the specified value
begins with a `+' character, then the specified key types will
be appended to the default set instead of replacing them. The
default for this option is:
ecdsa-sha2-nistp256-cert-v01@openssh.com,
ecdsa-sha2-nistp384-cert-v01@openssh.com,
ecdsa-sha2-nistp521-cert-v01@openssh.com,
ssh-ed25519-cert-v01@openssh.com,
ssh-rsa-cert-v01@openssh.com,
ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521,
ssh-ed25519,ssh-rsa
If hostkeys are known for the destination host then this default
is modified to prefer their algorithms.
The list of available key types may also be obtained using the
-Q option of ssh(1) with an argument of ``key''.
HostKeyAlias
Specifies an alias that should be used instead of the real host
name when looking up or saving the host key in the host key
database files. This option is useful for tunneling SSH connec-
tions or for multiple servers running on a single host.
HostName
Specifies the real host name to log into. This can be used to
specify nicknames or abbreviations for hosts. If the hostname
contains the character sequence `%h', then this will be replaced
with the host name specified on the command line (this is useful
for manipulating unqualified names). The character sequence
`%%' will be replaced by a single `%' character, which may be
used when specifying IPv6 link-local addresses.
The default is the name given on the command line. Numeric IP
addresses are also permitted (both on the command line and in
HostName specifications).
IdentitiesOnly
Specifies that ssh(1) should only use the authentication iden-
tity and certificate files explicitly configured in the ssh_con-
fig files or passed on the ssh(1) command-line, even if ssh-
agent(1) or a PKCS11Provider offers more identities. The argu-
ment to this keyword must be ``yes'' or ``no''. This option is
intended for situations where ssh-agent offers many different
identities. The default is ``no''.
IdentityAgent
Specifies the UNIX-domain socket used to communicate with the
authentication agent.
This option overrides the ``SSH_AUTH_SOCK'' environment variable
and can be used to select a specific agent. Setting the socket
name to ``none'' disables the use of an authentication agent.
If the string ``SSH_AUTH_SOCK'' is specified, the location of
the socket will be read from the SSH_AUTH_SOCK environment vari-
able.
The socket name may use the tilde syntax to refer to a user's
home directory or one of the following escape characters: `%d'
(local user's home directory), `%u' (local user name), `%l'
(local host name), `%h' (remote host name) or `%r' (remote user
name).
IdentityFile
Specifies a file from which the user's DSA, ECDSA, Ed25519 or
RSA authentication identity is read. The default is
~/.ssh/identity for protocol version 1, and ~/.ssh/id_dsa,
~/.ssh/id_ecdsa, ~/.ssh/id_ed25519 and ~/.ssh/id_rsa for proto-
col version 2. Additionally, any identities represented by the
authentication agent will be used for authentication unless
IdentitiesOnly is set. If no certificates have been explicitly
specified by CertificateFile, ssh(1) will try to load certifi-
cate information from the filename obtained by appending
-cert.pub to the path of a specified IdentityFile.
The file name may use the tilde syntax to refer to a user's home
directory or one of the following escape characters: `%d' (local
user's home directory), `%u' (local user name), `%l' (local host
name), `%h' (remote host name) or `%r' (remote user name).
It is possible to have multiple identity files specified in con-
figuration files; all these identities will be tried in
sequence. Multiple IdentityFile directives will add to the list
of identities tried (this behaviour differs from that of other
configuration directives).
IdentityFile may be used in conjunction with IdentitiesOnly to
select which identities in an agent are offered during authenti-
cation. IdentityFile may also be used in conjunction with Cer-
tificateFile in order to provide any certificate also needed for
authentication with the identity.
IgnoreUnknown
Specifies a pattern-list of unknown options to be ignored if
they are encountered in configuration parsing. This may be used
to suppress errors if ssh_config contains options that are
unrecognised by ssh(1). It is recommended that IgnoreUnknown be
listed early in the configuration file as it will not be applied
to unknown options that appear before it.
Include
Include the specified configuration file(s). Multiple pathnames
may be specified and each pathname may contain glob(3) wildcards
and, for user configurations, shell-like ``~'' references to
user home directories. Files without absolute paths are assumed
to be in ~/.ssh if included in a user configuration file or
/etc/ssh if included from the system configuration file.
Include directive may appear inside a Match or Host block to
perform conditional inclusion.
IPQoS Specifies the IPv4 type-of-service or DSCP class for connec-
tions. Accepted values are ``af11'', ``af12'', ``af13'',
``af21'', ``af22'', ``af23'', ``af31'', ``af32'', ``af33'',
``af41'', ``af42'', ``af43'', ``cs0'', ``cs1'', ``cs2'',
``cs3'', ``cs4'', ``cs5'', ``cs6'', ``cs7'', ``ef'', ``lowde-
lay'', ``throughput'', ``reliability'', or a numeric value.
This option may take one or two arguments, separated by white-
space. If one argument is specified, it is used as the packet
class unconditionally. If two values are specified, the first
is automatically selected for interactive sessions and the sec-
ond for non-interactive sessions. The default is ``lowdelay''
for interactive sessions and ``throughput'' for non-interactive
sessions.
KbdInteractiveAuthentication
Specifies whether to use keyboard-interactive authentication.
The argument to this keyword must be ``yes'' or ``no''. The
default is ``yes''.
KbdInteractiveDevices
Specifies the list of methods to use in keyboard-interactive
authentication. Multiple method names must be comma-separated.
The default is to use the server specified list. The methods
available vary depending on what the server supports. For an
OpenSSH server, it may be zero or more of: ``bsdauth'', ``pam'',
and ``skey''.
KexAlgorithms
Specifies the available KEX (Key Exchange) algorithms. Multiple
algorithms must be comma-separated. Alternately if the speci-
fied value begins with a `+' character, then the specified meth-
ods will be appended to the default set instead of replacing
them. The default is:
curve25519-sha256@libssh.org,
ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,
diffie-hellman-group-exchange-sha256,
diffie-hellman-group-exchange-sha1,
diffie-hellman-group14-sha1
The list of available key exchange algorithms may also be
obtained using the -Q option of ssh(1) with an argument of
``kex''.
LocalCommand
Specifies a command to execute on the local machine after suc-
cessfully connecting to the server. The command string extends
to the end of the line, and is executed with the user's shell.
The following escape character substitutions will be performed:
`%d' (local user's home directory), `%h' (remote host name),
`%l' (local host name), `%n' (host name as provided on the com-
mand line), `%p' (remote port), `%r' (remote user name) or `%u'
(local user name) or `%C' by a hash of the concatenation:
%l%h%p%r.
The command is run synchronously and does not have access to the
session of the ssh(1) that spawned it. It should not be used
for interactive commands.
This directive is ignored unless PermitLocalCommand has been
enabled.
LocalForward
Specifies that a TCP port on the local machine be forwarded over
the secure channel to the specified host and port from the
remote machine. The first argument must be [bind_address:]port
and the second argument must be host :hostport. IPv6 addresses
can be specified by enclosing addresses in square brackets.
Multiple forwardings may be specified, and additional forward-
ings can be given on the command line. Only the superuser can
forward privileged ports. By default, the local port is bound
in accordance with the GatewayPorts setting. However, an
explicit bind_address may be used to bind the connection to a
specific address. The bind_address of ``localhost'' indicates
that the listening port be bound for local use only, while an
empty address or `*' indicates that the port should be available
from all interfaces.
LogLevel
Gives the verbosity level that is used when logging messages
from ssh(1). The possible values are: QUIET, FATAL, ERROR,
INFO, VERBOSE, DEBUG, DEBUG1, DEBUG2, and DEBUG3. The default
is INFO. DEBUG and DEBUG1 are equivalent. DEBUG2 and DEBUG3
each specify higher levels of verbose output.
MACs Specifies the MAC (message authentication code) algorithms in
order of preference. The MAC algorithm is used for data
integrity protection. Multiple algorithms must be comma-sepa-
rated. If the specified value begins with a `+' character, then
the specified algorithms will be appended to the default set
instead of replacing them.
The algorithms that contain ``-etm'' calculate the MAC after
encryption (encrypt-then-mac). These are considered safer and
their use recommended.
The default is:
umac-64-etm@openssh.com,umac-128-etm@openssh.com,
hmac-sha2-256-etm@openssh.com,hmac-sha2-512-etm@openssh.com,
hmac-sha1-etm@openssh.com,
umac-64@openssh.com,umac-128@openssh.com,
hmac-sha2-256,hmac-sha2-512,hmac-sha1
The list of available MAC algorithms may also be obtained using
the -Q option of ssh(1) with an argument of ``mac''.
NoHostAuthenticationForLocalhost
This option can be used if the home directory is shared across
machines. In this case localhost will refer to a different
machine on each of the machines and the user will get many warn-
ings about changed host keys. However, this option disables
host authentication for localhost. The argument to this keyword
must be ``yes'' or ``no''. The default is to check the host key
for localhost.
NumberOfPasswordPrompts
Specifies the number of password prompts before giving up. The
argument to this keyword must be an integer. The default is 3.
PasswordAuthentication
Specifies whether to use password authentication. The argument
to this keyword must be ``yes'' or ``no''. The default is
``yes''.
PermitLocalCommand
Allow local command execution via the LocalCommand option or
using the ! Ns command escape sequence in ssh(1). The argument
must be ``yes'' or ``no''. The default is ``no''.
PKCS11Provider
Specifies which PKCS#11 provider to use. The argument to this
keyword is the PKCS#11 shared library ssh(1) should use to com-
municate with a PKCS#11 token providing the user's private RSA
key.
Port Specifies the port number to connect on the remote host. The
default is 22.
PreferredAuthentications
Specifies the order in which the client should try authentica-
tion methods. This allows a client to prefer one method (e.g.
keyboard-interactive) over another method (e.g. password). The
default is:
gssapi-with-mic,hostbased,publickey,
keyboard-interactive,password
Protocol
Specifies the protocol versions ssh(1) should support in order
of preference. The possible values are `1' and `2'. Multiple
versions must be comma-separated. When this option is set to
``2,1'' ssh will try version 2 and fall back to version 1 if
version 2 is not available. The default is `2'. Protocol 1
suffers from a number of cryptographic weaknesses and should not
be used. It is only offered to support legacy devices.
ProxyCommand
Specifies the command to use to connect to the server. The com-
mand string extends to the end of the line, and is executed
using the user's shell `exec' directive to avoid a lingering
shell process.
In the command string, any occurrence of `%h' will be substi-
tuted by the host name to connect, `%p' by the port, and `%r' by
the remote user name. The command can be basically anything,
and should read from its standard input and write to its stan-
dard output. It should eventually connect an sshd(8) server
running on some machine, or execute sshd -i somewhere. Host key
management will be done using the HostName of the host being
connected (defaulting to the name typed by the user). Setting
the command to ``none'' disables this option entirely. Note
that CheckHostIP is not available for connects with a proxy com-
mand.
This directive is useful in conjunction with nc(1) and its proxy
support. For example, the following directive would connect via
an HTTP proxy at 192.0.2.0:
ProxyCommand /usr/bin/nc -X connect -x 192.0.2.0:8080 %h %p
ProxyJump
Specifies one or more jump proxies as
[user@] host [:port] Multiple proxies may be separated by comma
characters and will be visited sequentially. Setting this
option will cause ssh(1) to connect to the target host by first
making a ssh(1) connection to the specified ProxyJump host and
then establishing a TCP forwarding to the ultimate target from
there.
Note that this option will compete with the ProxyCommand option
- whichever is specified first will prevent later instances of
the other from taking effect.
ProxyUseFdpass
Specifies that ProxyCommand will pass a connected file descrip-
tor back to ssh(1) instead of continuing to execute and pass
data. The default is ``no''.
PubkeyAcceptedKeyTypes
Specifies the key types that will be used for public key authen-
tication as a comma-separated pattern list. Alternately if the
specified value begins with a `+' character, then the key types
after it will be appended to the default instead of replacing
it. The default for this option is:
ecdsa-sha2-nistp256-cert-v01@openssh.com,
ecdsa-sha2-nistp384-cert-v01@openssh.com,
ecdsa-sha2-nistp521-cert-v01@openssh.com,
ssh-ed25519-cert-v01@openssh.com,
ssh-rsa-cert-v01@openssh.com,
ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521,
ssh-ed25519,ssh-rsa
The -Q option of ssh(1) may be used to list supported key types.
PubkeyAuthentication
Specifies whether to try public key authentication. The argu-
ment to this keyword must be ``yes'' or ``no''. The default is
``yes''.
RekeyLimit
Specifies the maximum amount of data that may be transmitted
before the session key is renegotiated, optionally followed a
maximum amount of time that may pass before the session key is
renegotiated. The first argument is specified in bytes and may
have a suffix of `K', `M', or `G' to indicate Kilobytes,
Megabytes, or Gigabytes, respectively. The default is between
`1G' and `4G', depending on the cipher. The optional second
value is specified in seconds and may use any of the units docu-
mented in the TIME FORMATS section of sshd_config(5). The
default value for RekeyLimit is ``default none'', which means
that rekeying is performed after the cipher's default amount of
data has been sent or received and no time based rekeying is
done.
RemoteForward
Specifies that a TCP port on the remote machine be forwarded
over the secure channel to the specified host and port from the
local machine. The first argument must be [bind_address:]port
and the second argument must be host :hostport. IPv6 addresses
can be specified by enclosing addresses in square brackets.
Multiple forwardings may be specified, and additional forward-
ings can be given on the command line. Privileged ports can be
forwarded only when logging in as root on the remote machine.
If the port argument is `0', the listen port will be dynamically
allocated on the server and reported to the client at run time.
If the bind_address is not specified, the default is to only
bind to loopback addresses. If the bind_address is `*' or an
empty string, then the forwarding is requested to listen on all
interfaces. Specifying a remote bind_address will only succeed
if the server's GatewayPorts option is enabled (see sshd_con-
fig(5)) .
RequestTTY
Specifies whether to request a pseudo-tty for the session. The
argument may be one of: ``no'' (never request a TTY), ``yes''
(always request a TTY when standard input is a TTY), ``force''
(always request a TTY) or ``auto'' (request a TTY when opening a
login session). This option mirrors the -t and -T flags for
ssh(1).
RevokedHostKeys
Specifies revoked host public keys. Keys listed in this file
will be refused for host authentication. Note that if this file
does not exist or is not readable, then host authentication will
be refused for all hosts. Keys may be specified as a text file,
listing one public key per line, or as an OpenSSH Key Revocation
List (KRL) as generated by ssh-keygen(1). For more information
on KRLs, see the KEY REVOCATION LISTS section in ssh-keygen(1).
RhostsRSAAuthentication
Specifies whether to try rhosts based authentication with RSA
host authentication. The argument must be ``yes'' or ``no''.
The default is ``no''. This option applies to protocol version
1 only and requires ssh(1) to be setuid root.
RSAAuthentication
Specifies whether to try RSA authentication. The argument to
this keyword must be ``yes'' or ``no''. RSA authentication will
only be attempted if the identity file exists, or an authentica-
tion agent is running. The default is ``yes''. Note that this
option applies to protocol version 1 only.
SendEnv
Specifies what variables from the local environ(7) should be
sent to the server. The server must also support it, and the
server must be configured to accept these environment variables.
Note that the TERM environment variable is always sent whenever
a pseudo-terminal is requested as it is required by the proto-
col. Refer to AcceptEnv in sshd_config(5) for how to configure
the server. Variables are specified by name, which may contain
wildcard characters. Multiple environment variables may be sep-
arated by whitespace or spread across multiple SendEnv direc-
tives. The default is not to send any environment variables.
See PATTERNS for more information on patterns.
ServerAliveCountMax
Sets the number of server alive messages (see below) which may
be sent without ssh(1) receiving any messages back from the
server. If this threshold is reached while server alive mes-
sages are being sent, ssh will disconnect from the server, ter-
minating the session. It is important to note that the use of
server alive messages is very different from TCPKeepAlive
(below). The server alive messages are sent through the
encrypted channel and therefore will not be spoofable. The TCP
keepalive option enabled by TCPKeepAlive is spoofable. The
server alive mechanism is valuable when the client or server
depend on knowing when a connection has become inactive.
The default value is 3. If, for example, ServerAliveInterval
(see below) is set to 15 and ServerAliveCountMax is left at the
default, if the server becomes unresponsive, ssh will disconnect
after approximately 45 seconds.
ServerAliveInterval
Sets a timeout interval in seconds after which if no data has
been received from the server, ssh(1) will send a message
through the encrypted channel to request a response from the
server. The default is 0, indicating that these messages will
not be sent to the server.
StreamLocalBindMask
Sets the octal file creation mode mask (umask) used when creat-
ing a Unix-domain socket file for local or remote port forward-
ing. This option is only used for port forwarding to a Unix-
domain socket file.
The default value is 0177, which creates a Unix-domain socket
file that is readable and writable only by the owner. Note that
not all operating systems honor the file mode on Unix-domain
socket files.
StreamLocalBindUnlink
Specifies whether to remove an existing Unix-domain socket file
for local or remote port forwarding before creating a new one.
If the socket file already exists and StreamLocalBindUnlink is
not enabled, ssh will be unable to forward the port to the Unix-
domain socket file. This option is only used for port forward-
ing to a Unix-domain socket file.
The argument must be ``yes'' or ``no''. The default is ``no''.
StrictHostKeyChecking
If this flag is set to ``yes'', ssh(1) will never automatically
add host keys to the ~/.ssh/known_hosts file, and refuses to
connect to hosts whose host key has changed. This provides max-
imum protection against trojan horse attacks, though it can be
annoying when the /etc/ssh/ssh_known_hosts file is poorly main-
tained or when connections to new hosts are frequently made.
This option forces the user to manually add all new hosts. If
this flag is set to ``no'', ssh will automatically add new host
keys to the user known hosts files. If this flag is set to
``ask'', new host keys will be added to the user known host
files only after the user has confirmed that is what they really
want to do, and ssh will refuse to connect to hosts whose host
key has changed. The host keys of known hosts will be verified
automatically in all cases. The argument must be ``yes'',
``no'', or ``ask''. The default is ``ask''.
TCPKeepAlive
Specifies whether the system should send TCP keepalive messages
to the other side. If they are sent, death of the connection or
crash of one of the machines will be properly noticed. However,
this means that connections will die if the route is down tempo-
rarily, and some people find it annoying.
The default is ``yes'' (to send TCP keepalive messages), and the
client will notice if the network goes down or the remote host
dies. This is important in scripts, and many users want it too.
To disable TCP keepalive messages, the value should be set to
``no''.
Tunnel Request tun(4) device forwarding between the client and the
server. The argument must be ``yes'', ``point-to-point'' (layer
3), ``ethernet'' (layer 2), or ``no''. Specifying ``yes''
requests the default tunnel mode, which is ``point-to-point''.
The default is ``no''.
TunnelDevice
Specifies the tun(4) devices to open on the client (local_tun)
and the server (remote_tun.)
The argument must be local_tun[:remote_tun.] The devices may be
specified by numerical ID or the keyword ``any'', which uses the
next available tunnel device. If remote_tun is not specified,
it defaults to ``any''. The default is ``any:any''.
UpdateHostKeys
Specifies whether ssh(1) should accept notifications of addi-
tional hostkeys from the server sent after authentication has
completed and add them to UserKnownHostsFile. The argument must
be ``yes'', ``no'' (the default) or ``ask''. Enabling this
option allows learning alternate hostkeys for a server and sup-
ports graceful key rotation by allowing a server to send
replacement public keys before old ones are removed. Additional
hostkeys are only accepted if the key used to authenticate the
host was already trusted or explicitly accepted by the user. If
UpdateHostKeys is set to ``ask'', then the user is asked to con-
firm the modifications to the known_hosts file. Confirmation is
currently incompatible with ControlPersist, and will be disabled
if it is enabled.
Presently, only sshd(8) from OpenSSH 6.8 and greater support the
``hostkeys@openssh.com'' protocol extension used to inform the
client of all the server's hostkeys.
UsePrivilegedPort
Specifies whether to use a privileged port for outgoing connec-
tions. The argument must be ``yes'' or ``no''. The default is
``no''. If set to ``yes'', ssh(1) must be setuid root. Note
that this option must be set to ``yes'' for RhostsRSAAuthentica-
tion with older servers.
User Specifies the user to log in as. This can be useful when a dif-
ferent user name is used on different machines. This saves the
trouble of having to remember to give the user name on the com-
mand line.
UserKnownHostsFile
Specifies one or more files to use for the user host key data-
base, separated by whitespace. The default is
~/.ssh/known_hosts, ~/.ssh/known_hosts2.
VerifyHostKeyDNS
Specifies whether to verify the remote key using DNS and SSHFP
resource records. If this option is set to ``yes'', the client
will implicitly trust keys that match a secure fingerprint from
DNS. Insecure fingerprints will be handled as if this option
was set to ``ask''. If this option is set to ``ask'', informa-
tion on fingerprint match will be displayed, but the user will
still need to confirm new host keys according to the Stric-
tHostKeyChecking option. The argument must be ``yes'', ``no'',
or ``ask''. The default is ``no''.
See also VERIFYING HOST KEYS in ssh(1).
VisualHostKey
If this flag is set to ``yes'', an ASCII art representation of
the remote host key fingerprint is printed in addition to the
fingerprint string at login and for unknown host keys. If this
flag is set to ``no'', no fingerprint strings are printed at
login and only the fingerprint string will be printed for
unknown host keys. The default is ``no''.
XAuthLocation
Specifies the full pathname of the xauth(1) program. The
default is /usr/bin/X11/xauth.
PATTERNS
A pattern consists of zero or more non-whitespace characters, `*' (a
wildcard that matches zero or more characters), or `?' (a wildcard that
matches exactly one character). For example, to specify a set of dec-
larations for any host in the ``.co.uk'' set of domains, the following
pattern could be used:
Dl Host *.co.uk
The following pattern would match any host in the 192.168.0.[0-9] net-
work range:
Dl Host 192.168.0.?
A pattern-list is a comma-separated list of patterns. Patterns within
pattern-lists may be negated by preceding them with an exclamation mark
(`!'.) For example, to allow a key to be used from anywhere within an
organization except from the ``dialup'' pool, the following entry (in
authorized_keys) could be used:
Dl from="!*.dialup.example.com,*.example.com"
FILES
~/.ssh/config
This is the per-user configuration file. The format of this
file is described above. This file is used by the SSH client.
Because of the potential for abuse, this file must have strict
permissions: read/write for the user, and not accessible by oth-
ers.
/etc/ssh/ssh_config
Systemwide configuration file. This file provides defaults for
those values that are not specified in the user's configuration
file, and for those users who do not have a configuration file.
This file must be world-readable.
SEE ALSO
ssh(1)
AUTHORS
OpenSSH is a derivative of the original and free ssh 1.2.12 release by
Tatu Ylonen. Aaron Campbell, Bob Beck, Markus Friedl, Niels Provos,
Theo de Raadt and Dug Song removed many bugs, re-added newer features
and created OpenSSH. Markus Friedl contributed the support for SSH
protocol versions 1.5 and 2.0.
July 22 2016 SSH_CONFIG(5)
Man(1) output converted with
man2html